Nomenclature for Screws - Revision history

Steffen at 00:46, 8 April 2018

2018-04-08T00:46:51Z

← Older revision		Revision as of 00:46, 8 April 2018
Line 26:		Line 26:

	<pre>		<pre>
	u9000.dat - ~Screw 44.5 x  5 Countersunk Slotted~~<BR />~~		u9000.dat - ~Screw 44.5 x  5 Countersunk Slotted
	u9013.dat - ~Screw 12 x  6 Pan Cruciform~~<BR />~~		u9013.dat - ~Screw 12 x  6 Pan Cruciform
	u9021.dat - ~Screw  6 x  5 Flat Slotted~~<BR />~~		u9021.dat - ~Screw  6 x  5 Flat Slotted
	u9022.dat - ~Screw  4 x  4 Beveled Triangular~~<BR />~~		u9022.dat - ~Screw  4 x  4 Beveled Triangular
	</pre>		</pre>

	[[Category:New Ideas for Future Official Parts Standards]]		[[Category:New Ideas for Future Official Parts Standards]]

Steffen at 00:46, 8 April 2018

2018-04-08T00:46:31Z

← Older revision		Revision as of 00:46, 8 April 2018
Line 4:		Line 4:
	___________________		___________________

	~~== Nomenclature for Screws ==~~
	~~Nomenclature: '''Screw length_(LDu) x thread_diameter_(LDu) {head type} {slot type}<BR/>~~
	~~'''~~

	At present we have the following {head type}:~~<BR />~~		A suggestion by
	- Countersunk~~<BR />~~		--[[User:Mikeheide\|Mikeheide]] 09:56, 10 July 2011 (EDT)
	- Pan~~<BR />~~
	- Flat~~<BR />~~		Nomenclature: '''Screw length_(LDu) x thread_diameter_(LDu) {head type} {slot type}'''
	- Beveled~~<BR />~~
			At present we have the following {head type}s:
			* Countersunk
			* Pan
			* Flat
			* Beveled

	Screw length is measured from the flat underside of the head, except for Countersunk when it is measured from the flat top surface.		Screw length is measured from the flat underside of the head, except for Countersunk when it is measured from the flat top surface.

	At present we have the following {slot type}:~~<BR />~~		At present we have the following {slot type}s:
	- Slotted~~<BR />~~		* Slotted
	- Cruciform~~<BR />~~		* Cruciform
	- Triangular~~<BR />~~		* Triangular

	~~'''~~Examples~~:'''<BR />~~		== Examples ==
	<~~CODE~~>
			<pre>
	u9000.dat - ~Screw 44.5 x  5 Countersunk Slotted<BR />		u9000.dat - ~Screw 44.5 x  5 Countersunk Slotted<BR />
	u9013.dat - ~Screw 12 x  6 Pan Cruciform<BR />		u9013.dat - ~Screw 12 x  6 Pan Cruciform<BR />
	u9021.dat - ~Screw  6 x  5 Flat Slotted<BR />		u9021.dat - ~Screw  6 x  5 Flat Slotted<BR />
	u9022.dat - ~Screw  4 x  4 Beveled Triangular<BR />		u9022.dat - ~Screw  4 x  4 Beveled Triangular<BR />
	</~~CODE~~>		</pre>
	~~--[[User:Mikeheide\|Mikeheide]] 09:56, 10 July 2011 (EDT)~~

	[[Category:New Ideas for Future Official Parts Standards]]		[[Category:New Ideas for Future Official Parts Standards]]

Steffen: Created page with "This is a historic page with suggestions from that time. It needs to be reworked to document the status of today (2018). ___________________ == Nomenclature for Screws == N..."

2018-04-08T00:44:20Z

Created page with "This is a historic page with suggestions from that time. It needs to be reworked to document the status of today (2018). ___________________ == Nomenclature for Screws == N..."

New page

This is a historic page with suggestions from that time. It needs to be reworked to document the status of today (2018).

___________________

== Nomenclature for Screws ==
Nomenclature: '''Screw length_(LDu) x thread_diameter_(LDu) {head type} {slot type} 
'''

At present we have the following {head type}: 
- Countersunk 
- Pan 
- Flat 
- Beveled 
Screw length is measured from the flat underside of the head, except for Countersunk when it is measured from the flat top surface.

At present we have the following {slot type}: 
- Slotted 
- Cruciform 
- Triangular 

'''Examples:''' 
<CODE>
u9000.dat - ~Screw 44.5 x  5 Countersunk Slotted 
u9013.dat - ~Screw 12 x  6 Pan Cruciform 
u9021.dat - ~Screw  6 x  5 Flat Slotted 
u9022.dat - ~Screw  4 x  4 Beveled Triangular 
</CODE>
--[[User:Mikeheide|Mikeheide]] 09:56, 10 July 2011 (EDT)

[[Category:New Ideas for Future Official Parts Standards]]